Test Cards
See Also: Cards, Extender Cards, Probe Cards, POST Cards
-
Product
Bi-Directional Differential-TTL I/O PXI Card
GX5641 Series
Digital I/O Module
The GX5641 is a 3U PXI instrument card that can be used for general data acquisition, process control, Automatic Test Equipment (ATE), functional test, and factory automation applications. The GX5641 consists of 64 bi-directional TTL-differential I/O channels. Each channel has two ports (TTL and differential) which can be individually set to operate in either conversion or static I/O modes.
-
Product
FPGA Mezzanine Card
FMC134
-
The FMC134 provides customers with a high bandwidth and high channel count I/O solution that is ideal for multi-channel receivers in a wide range of applications.With four 12-bit analog-to-digital channels up to 3.2GSPS or two analog channels up to 6.4GSPS, the FMC134’s design is based on the Texas Instruments™ ADC12DJ3200 and is mechanically and electrically compliant with the FMC+ standard (VITA 57.4), the next generation of small form factor expansion I/O for high performance FPGA-based systems.
-
Product
Controller Card
GPIB-PCI-XL
Controller
The GPIB-PCI-XL is a flexible PCI GPIB controller card that converts any PC with a PCI bus slot into a GPIB controller.
-
Product
PCI Card
EXC-4000PCI/xx
-
Each channel using the M4K1553PxS (RT validated) module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.NOTE: the M4K1553PxS module is NOT compatible to the M4K1553MCH module.The EXC-4000PCI/xx is supplied with C drivers (including source code), Merlin+ Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. Mating connector provided for I/O connection.
-
Product
Digital I/O Card
PCI-DIO-120
-
The PCI-DIO-120, PCI-DIO-96 and PCI-DIO-72 are parallel digital input/output cards designed for use in PCI-Bus computers. The same printed circuit board is used for all three models and is populated for 120 bits, 96 bits and 72 bits respectively. The card is 12.2 inches (310 mm) long and may be installed in any 5-volt PCI slot in IBM and compatible computers.
-
Product
FPGA Mezzanine Card
FMC424
-
Electrically compliant with the VITA 57.1 standard, the FMC424 is compatible with Abaco Systems' FPGA carrier cards offering high pin count connectors. It also allows for the option to stack an additional FMC over it.
-
Product
Conformance Test System
TS8980
Test System
The R&S®TS8980 is the most compact full range conformance testing solution on the market for testing in line with requirements from GCF, PTCRB and regulatory bodies. It supports the entire device certification process for RF and RRM, covering the widest range of technologies including 5G NR based on 3GPP and carrier acceptance specifications. The test system is available in various configurations to cover the required scope of testing.
-
Product
ESD Test System
58154 Series
Test System
ESD (Electrostatic Discharge) Test Systems are PXI/PCI controlled module to simulate electrostatic discharge pulse during electronic device testing. The 58154 series offer both ESD STM5.1-2001-Human Body Model and ESD STM5.2-1999-Machine Model. The user friendly software offers programmable and flexible features, such as sampling test on a wafer, ESD model, ESD pulse polarity, ESD pulse interval in a sequence, and automatic testing function.
-
Product
Multisite Probe Card
T300 ButtonTile™
-
The Celadon T300™ probe cards are designed for long-term, multi-site, high-density wafer level reliability or burn-in tests up to 400°C. In today’s economic environment, conventional reliability data is needed quickly while eliminating the cost, electrical stress, and delay of parts packaging while maintaining a wafer performance map.
-
Product
PMC Carrier for PCI Card Interface
TPCI270
-
The TPCI270 is a standard 33 MHz, 32 bit PCI carrier for a single PMC Card. Itprovides PMC front I/O and PMC P14 rear I/O. This PMC to PCI adapter is used to build modular, flexible and cost effective I/O solutions with PMC devices in standard PCI systems.
-
Product
6U Vertical Card
440
-
VECTOR Electronics and Technology, Inc.
Chassis for vertical card installation
-
Product
Reflective Memory Node Card
PMC-5565PIORC
-
The PMC-5565PIORC Reflective Memory node card provides a high-speed, low latency, deterministic interface that allows data to be shared between up to 256 independent systems (nodes) at rates up to 170 Mbyte/s. Each Reflective Memory board may be configured with 128 MB or 256 MB of onboard SDRAM.The local SDRAM provides fast Read access times to stored data.
-
Product
Multiprotocol Serial Card
LPCI-COM-8SM
-
The LPCI-COM Series are eight or four-port asynchronous serial communication cards designed for use in PCI bus computers. The cards support RS-232, RS-422, and/or RS-485 communications which can be selected on a port by port basis. The cards are 6.6 inches in length and 2.21 inches seated height and may be installed in any 3.3 or 5-volt PCI or PCI-X expansion slot.
-
Product
96-CH High-Driving DIO Card
PCI-7396
Analog Input Module
The PCI-7396 is 96-bit parallel digital input/output (DIO) cards designed for industrial applications. The PCI-7396 emulates four 8255 Programmable Peripheral Interface (PPI) chips. Each PPI offers three 8-bit DIO ports which can be accessed simultaneously. The total 12/6 ports can be configured as input or output independently.
-
Product
Message Based Intelligent Interface Card
IIB-3910-VXI
-
The IIB-3910-VXI is message based intelligent interface card for dual redundant 3910 and 3838 applications. It gives full 3910 and 3838 test, simulation and bus analysis capability on the VXI bus, providing 3910, 3838 1553A, and 1553B variants in a single card. Each channel supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with passive Bus Monitor, and an independent Chronological Bus Monitor (CBM). Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides dual redundant prEN3715 compatible 3910 interface, with variable amplitude dual redundant 3838 interfaces. External trigger-in and trigger-out are provided, with both Primary and secondary bus coupling for direct and stub bus, with access to internal 1553 bus, on the front panel.
-
Product
Smart Card Reader
UTC-510P-S01E
-
Memory card -Synchronous 2-line, 3-line and I2C interface. CPU card -Complies with ISO7816-1,2,3,T=1 and T=0 protocol. Reliability: 200,000 cycles.
-
Product
XMC Display Control Card
XM26001
-
LinkedHope Intelligent Technologies Co.,Ltd.
XM26001 is a graphics, image processing and computing single-board computer independently developed by Linghao Intelligent®. It uses the AMD G series APU GX-210HA by default, integrating the CPU, GPU, south bridge and north bridge on one silicon chip.
-
Product
Multiprotocol Serial Card
PCIe-COM-8SM
-
ACCES I/O’s PCI Express multi-port multi-protocol serial communication cards deliver eight (PCIe-COM-8SM) or four (PCIe-COM-4SM), high-speed serial communication ports for use in a wide variety of applications. The cards were designed to offer serial compatibility with the PCI Express bus and to be used by system integrators and manufacturers in the design of industrial and commercial systems.
-
Product
Digital Input/Output and Counter/Timer Card
PCI-DIO-96C3
-
This is a 96 line digital input/output card with counter/timer capabilities designed for use in high I/O density application requirements. I/O connections are made via four 50-pin header connectors. The card is 12.25 inches long (312 mm) and may be installed in any full-length 5V PCI-bus (or PCI-X bus) slot in X86 type PC’s.
-
Product
Extender Card
-
The IEEE extender card, referred to as board PWB1000281-03. Extender card to allow for testing and debugging of the chassis assembly. This board was originally an Intel design that Dynamic Engineering was authorized by Intel to re-create
-
Product
3U VPX DSP Processor Card
VPX3-450
-
Curtiss-Wright Defense Solutions
Many FPGA processor modules require a separate processor card to control the FPGA module. The VPX3-450 module combines a Xilinx Virtex-5 FPGA and a PowerPC processor on a single module along with a flexible XMC site for bringing different types of IO directly into the FPGA. Therefore, in a single slot, a hybrid solution can be provided.
-
Product
Functional Testing and Test Engineering
-
Customer-supplied or developed in-house• Ruggedization of existing (lab-built) fixtures• Co-develop hardware/software• Deployment, implementation, and training• Engineering evaluation tools• Design verification• Medical device evaluation• Manufacturing test systems• Verification test systems• Go/No-go tests• Serialization, recordkeeping, and datalogging• Troubleshooting failed units with other test platforms
-
Product
Test Adapters / Aeroflex Test System
52xx / 5300
-
We develop and manufacture test adapters for your existing interface including documentation and test program
-
Product
Miscellaneous Function Cards
ProDAQ 3900 Series
-
The ProDAQ 3900 Series function cards are high-density cards that fit into ProDAQ VXIbus motherboards and LXI function card carriers. ProDAQ instruments are versatile, providing users with the highest channel density and functionality available on the market.
-
Product
Indicators - Test
-
Measures the deflection of the arm, the probe does not retract but swings in an arc around its hinge point.
-
Product
Routing Card
SET-2010
-
With 64 single-ended or 32 differential channels, the SET-2010 provides exceptional signal routing capabilities in a small form factor. Unlike traditional routing matrix cards, the SET-2010 is designed specifically for the challenges of signal routing in HIL systems.
-
Product
Microwave Testing
140
-
The PICOPROBE® MODEL 140, a high performance microwave probe which incorporates a WR-8 waveguide with our patented coaxial design techniques, has inherent low loss and low dispersion characteristics.
-
-
Product
Single Function MIL-STD-1553 Test & Simulation PCIe Card
ASE1553M-x
Simulator
Single Function MIL-STD-1553 Test and Simulation module for PCIe with 1, 2 or 4 dual redundant streams.
-
Product
Dynamics Testing
-
Dynamics testing evaluates a product’s ability to withstand stresses occurring during normal and adverse operating conditions. These tests can also include conditions found during transport and product installation. Dynamics testing is common in commercial, industrial, aerospace and military applications.
