Device Under Test
a specific purpose component or module check; ex. substantial component of a PCB.
See Also: DUT, Unit Under Test, EUT
-
Product
Power Quality Analyzer
PQM-710
-
PQM-710 power quality analyzer is an advanced product for wide type of measurements, analysis and recording of network parameters 50/60 Hz and the power quality diagnostic according to European standard EN. PQM-710 is an innovative model with a wireless communication Wi-Fi , which allows for automatic pairing with the included tablet, with a large 10" touch screen. Tablet allows full operating of the analyzer, live data preview and the reading and analysis of data stored in the internal memory. With this solution, the PQM-710 is an unique device that combines the advantages of the analyzer with built-in display and typical portable analyzers (known as Black Boxes).With the tablet you can very fast checked the device under test. On the other hand, you can leave the analyzer module for multi-measurements as a typical logger without display. You can very fast diagnose the machine under test using the tablet. On the other hand, you can leave the analyzer module itself for many days measurement as a typical logger without display.
-
Product
NI-9229, ±60 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Module
779785-02
Voltage Input Module
±60 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Module - The NI‑9229 performs differential analog input. The NI‑9229 is an effective general-purpose analog module because of its resolution, sample rate, and input range. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating.
-
Product
VXI D/A Converters
-
With Keysight Technologies' digital to analog converters, you can control devices under test or simulate sensors in a VXI-based test system.
-
Product
Scienlab Measurement And Control Module
SL1064B
Communications Module
The Measurement & Control Module SL1064B is a rack-mount gateway for CAN- and LIN-buses with up to 6 channels. It can be used as a configurable communication interface between Scienlab Battery Test Systems and devices under test (especially their BMS) as well as additional components using CAN communication.
-
Product
Functional Test
UTS
Functional Test
The UTS functional test system is perfect for electronics manufacturing operations that have a mix of products where operators load and unload devices under test (DUT) and routinely change out fixtures for each type of DUT.
-
Product
Automated Optical Inspection (AOI)
-
Automated optical inspection (AOI) is an automated visual inspection of printed circuit board (PCB) (or LCD, transistor) manufacture where a camera autonomously scans the device under test for both catastrophic failure (e.g. missing component) and quality defects (e.g. fillet size or shape or component skew). It is commonly used in the manufacturing process because it is a non-contact test method.
-
Product
Line-impedance stabilisation network
NNB 21 set
-
The NNB 21 line impedance stabilization network is designed for measuring of grid bound interferences of a device under test according to the satndard CISPR 25/ISO 7637. It measures the RF interference, which couples into the vehicle electrical system. Measurements during the development in a frequency range from 100 kHz to 1GHz can be carried out.
-
Product
Test Leads Adapter Sets
-
A physical device used to connect electronic test equipment to a device under test.
-
Product
Qualification Tester
LQ404
-
Computer Gesteuerte Systeme GmbH
The qualification tester LQ402 is designed to support up to 12 DUTs (Device under Test), for which the loads are installed in separate load boxes. The system consists out of 3 cabinets. One is for the electronic components with the primary measurement devices and the other two hold the 12 load boxes.
-
Product
Test Fixtures-Assemblies
-
Qmax Test Technologies Pvt. Ltd.
Test Clips are available for various types of DIP ICs like 8, 14, 16, 20, 24, 28, 40, 48 & 64. These can be supplied with or without connectors and cables for interfacing to Qmax Testers. Test Pins in the clips are gold plated and engineered for good contact with the Device Under Test. It is designed for long life and trouble free operation. For easy handling the clips are provided with metal covers.
-
Product
Power Profiler, DC Energy Analyzer, Power Supply, Digital Multimeter, Source Measure Unit, Power Debugger
Otii Ace Pro
-
Otii Ace Pro is the big brother to Otii Arc, and is an instrument that can precisely source voltage (up to 25 V) and current (up to 5A) and simultaneously measures voltage and/or current with a high sample rate (50ksps) and low step size. It computes power and energy and enables engineers and developers to easily see and optimize the energy consumption and battery life of their devices under test.
-
Product
Dead Weight Tester
-
Nagman Instruments & Electronics Pvt. Ltd
Dead Weight Tester are a simple, low cost instrument to calibrate pressure devices. It basically works on the pressure balance principle with calibrated weights used to apply pressure to an area. When the pressure balance reaches zero, the pressure device under test is considered calibrated. Nagman’s range of dead weight tester are known for their best quality, industrial grade build with quick stabilization and ease to use.
-
Product
PathWave Lab Operations For Battery Test
EP1150A
-
PathWave Lab Operations for Battery Test enables efficient planning and coordination of your entire battery test laboratory. It manages all resources, including test fields, test systems, and your device under test (DUT). PathWave provides an integrated, web-based lab management platform that helps you modernize your test workflows, eliminating legacy paper-based processes, and increasing data integrity and traceability.
-
Product
RF Shielded Box
TS7124
-
R&S®TS7124 RF shielded boxes enable reliable and reproducible measurements in shielded test environments. The R&S®TS7124 shielded box provides high shielding effectiveness, a good antenna coupling factor and a rugged mechanical design for reproducible results. RF test boxes have been designed not only for product designers or product optimization but also for production lines of wireless devices under test. The soft close feature makes the shielded box safer to operate.
-
Product
Regenerative Power System, 500 V, 20 A, 5 kW, 400/480 VAC
RP7961A
DC Power Supply
The Keysight RP7961A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test. The regenerative capability enables the energy normally consumed to be returned to the grid cleanly, saving costs associated with energy consumption and cooling.
-
Product
PXIe-4142, 4-Channel, ±24 V, 150 mA PXI Source Measure Unit
782430-01
Source Measure Unit
PXIe, 4-Channel, ±24 V, 150 mA PXI Source Measure Unit - The PXIe-4142 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote (4-wire) sensing for accurate measurements. The fast sample rate of the PXIe-4142 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules.
-
Product
Test Probe
-
Beijing KeHuan Century EMC Technology Co,.LTD
Is a physical device used to connect electronic test equipment to a device under test (DUT).
-
Product
CMX RF Port Extender
CMX-Z25
-
Complex devices under test (DUT) come with additional antenna ports to support low, mid and high bands - and advanced MIMO schemes such as 4x4 MIMO. The R&S®CMX-Z25 is the solution: Up to 16 DUT ports can be supported with just 4 ports from R&S®CMX500. So even prototypes of 5G smartphones, tablets, laptops or industrial modules with an extended number of antenna ports can now be connected to a single R&S®CMX500. Together with the scalable CMX architecture any 5G and 5G Advanced mobile device can now be tested in one go - without recabling or 3GPP band combo limitations.
-
Product
PXI-4130, ±20 V, ±2 A DC, 40 W PXI Source Measure Unit
779647-31
Programmable Power Supply
±20 V, ±2 A DC, 40 W PXI Source Measure Unit - The PXI‑4130 is a programmable source measure unit (SMU). It has a single isolated SMU channel that offers a four-quadrant output that incorporates remote (4‑wire) sense. With its five current ranges, it is ideal for transistor characterization that requires accurately sourcing a constant current or voltage while sweeping another current. The PXI‑4130 also includes a utility channel that can source either current or voltage. This PXI SMU can act as either a constant voltage source or a constant current source, with a settable compliance limit for either mode. In addition, you can enable remote sense on the SMU channel to maximize voltage output and measurement accuracy on your device under test (DUT) for high-precision applications.
-
Product
HandyScope HS6-DIFF With SureConnect: 500 MS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-500XMS-W5
-
The only oscilloscope in the world that has:- SafeGround, differential input channels that can be switched to single ended.SureConnect, auto-detects a true connection between the probe tip and the device under test.- CMI interface.- USB 3.0 interface, 5Gb/s data transfer- Lowest noise
-
Product
Spectral Response SystemsQuantum Efficiency SystemsIPCE Measurement Systems
-
QE system provides electronics and software designed for fully automated measurement of external quantum efficiency of solar cells. All systems include probes and a fixed plate sample stage for samples up to 150 mm x 150 mm. The main system components include: custom designed software, measurement electronics, and computer system (Windows 8 operating system). The measurement involves focusing monochromatic light to a spot on the device under test, then accurately measuring the photon flux and current from the test cell. The system utilizes a dual beam configuration with lock-in detection, providing an absolute accuracy of ±3%. The QE system uses a grating monochrometer with silicon/InGaAs/Ge detectors. The system includes automatic order sorting filters and two light sources for monochromatic illumination (a Xenon- arc lamp and a halogen lamp). A single lock-in amplifier is used to measure both the reference detector and test device. The main system comes with all the hardware needed to measure quantum efficiency, a fixed plate sample stage and probes.
-
Product
RSE Wireless EMC Spurious Emission
TS8996
Test System
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
Product
Test Port Adapter Set, 3.5 Mm To 3.5 Mm
85130D
-
The Keysight 85130D test port adapter protects the test set port from being directly connected to the device under test. These adapters have a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 3.5 mm to PSC-3.5 mm male adapter and a 3.5 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 28 dB or better.
-
Product
Three-Phase compact Electric Power/Energy
MC133C
-
The Model MC133C is a compact single housed three phase electric power/energy calibrator. It can supply the device under test with precision one phase AC voltage and current with calibrated phase shift along with DC voltage and current. Output voltage can be set in five ranges up to 280V and output current in six ranges up to 30A.
-
Product
NI-9228, ±60 V, 1 kS/s/ch, 24-Bit, Simultaneous Input, 8-Channel C Series Voltage Input Module
783861-01
Voltage Input Module
±60 V, 1 kS/s/ch, 24-Bit, Simultaneous Input, 8-Channel C Series Voltage Input Module - The NI‑9228 performs differential analog input. With channel-to-channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. The NI‑9228 is simultaneous sampling with two options for filtering: a low-latency filter or a 50/60 Hz rejection filter. The low-latency filter enables users to use this module in industrial or control applications while getting better external noise rejection.
-
Product
NI-9239 , ±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
780181-01
Voltage Input Module
±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9239 performs differential analog input. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating. Designed for both speed and accuracy, the NI‑9239 is an effective general-purpose analog module because of its resolution, sample rate, and input range.
-
Product
Vector Impedance Analyser
TE3000
-
The TE3000 Vector Impedance Analyser is a portable desktop instrument designed for high accuracy impedance measurement. The probe style construction and small output signal make it ideal for "in circuit" impedance characterisation of small signal devices without the risk of damage to the device under test. The TE3000 comes factory calibrated to the tip of the probe with optional custom calibration. Turn it on, set the frequency, take a measurement, and display the results in any format.
-
Product
MEMS Device-Oriented Testers
-
Are your test requirements oriented to defined families of devices, with common characteristics? You do not need to purchase an expensive, general-purpose mixed signal tester: You can rely on SPEA DOT 100, a system designed to answer the test requirements of MEMS and other low-pin-count devices at an incredibly low cost.The DOT 100 is based on a revolutionary per-device architecture: each device under test has a dedicated CPU managing the entire test process, while each card hosts all the resources for the parallel test of 3 devices, in the size of a postcard.
-
Product
Electromechanical Transfer Switches up to 40 GHz
-
Fairview Microwave’s line of electromechanical relay transfer switches can be utilized for numerous applications to increase system level capabilities and can help simplify the overall design approach. With two input and two output ports, transfer switches can connect two different instruments with two devices under test. Additionally, they can be used as drop-out switches, for signal reversal or to bypass a component under test. These products are typically used in military communications and broadcast systems, SATCOM, test & measurement, instrumentation applications and are suitable for aircraft use.
-
Product
2-Axis Rate and Position Tables
-
When a device under test needs to be stimulated with simultaneous movements around two axes, then a product from the ACUTRONIC two-axis motion simulator range is the right choice. Due to their independent motion simulation in two axes they are very versatile: they are used as Inertial Guidance Test Systems (IGTS), for HardWare-In-the-Loop (HWIL) testing, for the test of optronic pointing devices, and many more applications.
