Analog Input Output
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
Product
3-CH RTD Input Module
ND-6013
Data Acquisition Module
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
SHC68-68-A2, 68-Pin VHDCI Male to 68-Pin SCSI Female Analog Cable
157599-02
Multifunction Cable
SHC68-68-A2, 68-Pin Male VHDCI to 68-Pin Female SCSI, 2m Cable. For use with the PXIe-6738 and PXIe-6739.
-
Product
4 Channels, 28-90 Vrms Input, 47 Hz-1 kHz
LD5
-
A linear variable differential transformer (LVDT) is a type of electrical transformer/transducer used for measuring linear displacement (position). A counterpart to this device used for measuring rotary displacement is called a rotary variable differential transformer (RVDT). The RVDT is like an LVDT in that it measures a positional displacement, however, the displacement, which is still a linear proportional function, is based on rotary instead of linear positional movement.
-
Product
PXI 8 Slot BRIC 230x8 1-Pole Dual Analog Bus (5 sub-cards)
40-560A-121-230X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
32-CH Discrete Output Daughter Board Module
HSL-DO32-DB-N
Digital Output Module
*Slave ID consumption: 2 - N: for 32-CH NPN sinking type outputs*Photo couple isolation voltage: 2500Vrms*Output switching capacity: Single channel 500mA; all channels 60mA at 24VDC*Output response time:ON OFF: 180µs, OFF ON: *1.2µsTerminal Base:HSL-TB64 or HSL-TB32U-DIN
-
Product
16-Ch Isolated Digital Input And 16-Ch Relay USB 3.0 I/O Module
USB-5862
-
USB 3.0 SuperSpeedDaisy chainable by built in USB hub16-ch Isolated Digital Input and 16-ch Form A-type Relay OutputWide input voltage range (10 ~ 30 VDC)High-voltage isolation on input channel (2,500 VDC )Quick removable European type connectorLED indicators for I/O statusSupported operating systems: Windows 10/11
-
Product
Plug and Play Potentiometer Input Module
DSCUSB-PT
-
The DSCUSB-PT is a compact, high-precision potentiometer input module; converting a resistance based input (potentiometer) to a digital output. Can be used with resistance based sensors to indicate position, rotation and angle. Aimed at applications which require high accuracy. Simply by plugging the device into a PC, data can be extracted from the potentiometer input to the DSCUSB-PT for a wide range of applications. This is achieved using the DSCUSB Toolkit software, which is a simple configuration tool designed specifically for configuring DSCUSB modules. It allows configuration, calibration, logging and parameter management of the modules.
-
Product
(115×145×33mm) High Power Multi-ports Output CATV FTTP EYDFA Module
EATV5400x-FM05S
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai EATV5400x-FM05S series is a low noise, high performance, high power multi-ports EYDFA module, which is specially designed for CATV system. It offers a flexible and low-cost FTTx solution for CATV large area coverage of metropolises and medium-sized cities.
-
Product
1 GHz, 2 Analog Channels Oscilloscope
DSOX3102A
Oscilloscope
1 GHz2 analog channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add memory, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
Oscilloscope, 1 GHz Bandwidth, 8 Input Channels, 50 Mpts/ch, 10GS/s
WaveRunner 8108HD
Oscilloscope
1 GHz, 8 Ch, 12 bits, 10 GS/s, 50 Mpts/Ch High Definition Oscilloscope.
-
Product
32-CH Discrete Output Modules with U Profile
HSL-DO32-UD
Digital Output Module
*UD type is suitable for screw type wiring. Each wire to sensors or actuators can be fixed by the screw terminal*RJ-45 phone jack for easy installation*Compact and single board design to meet space limitation and cost-effective requirement*Support 32 DO channels*Transmission speed: 3/6/12 Mbps
-
Product
NI-9477, 60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module
780174-01
Digital Module
60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module - The NI‑9477 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. Each channel is compatible with signals from 5 V to 60 V and … features isolation from channel‑to‑earth ground. You can wire the NI‑9477 channels in parallel to sink up to 20 A of current per module (1 A per channel maximum).
-
Product
Bench Power Supply, Single, Adjustable, Fixed, 1 Output, 13.3 V, 14.5 V, 15 A
72-8110
-
The 72-8110 is a compact switch mode Power Supply features a very compact footprint that makes it an ideal match for portable communications equipment. Its 50% duty cycle surge rating is comes in handy in demanding transmitting situations. It is also perfect for two-way radio (including HF) and audio equipment including auto sound and multimedia systems. This fixed voltage switch mode power supply is designed with high RFI stability and is especially suitable for two-way radio and communications equipment. Constant current circuitry is used for overload, short-circuit and over-temperature protection. Output current and voltage drop to a safe level when any fault occurs. This power supply also has over voltage protection to prevent connected equipment from damage.
-
Product
PCI Express 8 Reed Relay Output
8012eS
-
The 8012eS PCI Express digital interface provides eight optically isolated inputs and eight Reed relay outputs (SPST). The isolated inputs are non-polarized and rated for 3-30 VDC. Optical isolation protects the PC and other sensitive equipment from the voltage spikes and ground loop currents that are common to industrial environments.
-
Product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787456-01
Interface
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a … high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
Product
Isolated Analog Expansion Board
MSXB 085
-
The MSXB 085 Isolated Analog Expansion Board provides isolated analog inputs and isolated analog outputs for DAP systems. Use these boards to eliminate ground currents – a potential source of noise in your measurement and control signals – and eliminate timing skew.
-
Product
Oscilloscope, 65 GHz Bandwidth, 4 Input Channels, 160 GS/s Max Sample Rate
LabMaster 10 Zi-A 65 GHz Systems
Oscilloscope
65 GHz, 160 GS/s, 64 Mpts/Ch Digital Bandwidth Interleaved Acquisition Module, 50 Ohm Input. Also operates in 36 GHz, 80 GS/s, 4ch, 32 Mpts/Ch mode.
-
Product
4-CH RTD Thermal Input EtherCAT Module
EPS-3504
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
PCI Express Analog and Digital I/O
826
-
Six advanced 32-bit counters Directly supports incremental encoders, pwm/pulse generation, frequency/pulse/period measurement 16 analog inputs, 16-bit, 300 ks/s 8 analog outputs, 16-bit, 900 ks/s 48 digital I/Os with edge capture Watchdog timer, 3 stages
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 125 MS/s on 4 Channels, 4 Single-Ended Inputs
DN2.596-04
Digitizer
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Analog Meters
-
Weschler analog meters are available in ANSI switchboard styles, as well as standard industry panel meter sizes. Made in USA.
-
Product
Manometer – Thermometer Data Logger – 2 Inputs
HD2124.2
-
Manometer-Thermometer Data Logger with two inputs for SICRAM module PP471 to connect probes TP704 and TP705 series.
-
Product
75-Watt DC/DC Converter; Single Output
55KS1
DC Converter
NAI’s 55KS1 is a 75-Watt DC/DC Converter that accepts a +28 VDC input. This COTS unit provides full-power, single output, at a baseplate temperature of +100° C.
-
Product
PXI 8 Slot BRIC 368x8 1-Pole Dual Analog Bus (8 sub-cards)
40-560A-121-368X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI Digital IO: 32 inputs, 32 outputs, 0.3V to 50V
M9187A
Digital I/O Module
The M9187A has 32 input channels that can be used for comparing inputs to user-defined thresholds between 0.3V and 50V, with 12mV setting resolution. Each input is protected up to 100V. In addition, the 32 output channels use a high current to drive the output high or low, and are capable of sourcing 0.4A from the high side or 0.5A sink from the low side of each channel. These outputs are protected against over-voltage or over-current conditions. Choose from the durable connector block or the standard cable connections.
-
-
Product
Oscilloscope: 70/100/200 MHz, 4 Analog Channels
DSOX1204A
Oscilloscope
4 channel model of the InfiniiVision 1000 X-Series entry-level oscilloscopes that can be upgraded from 70 MHz to 100 MHz or 200 MHz
-
Product
150-Watt AC/DC Power Supply; Dual Output
56MD1
Programmable Power Supply
NAI’s 56MD1 is a 150 Watt AC/DC Power Supply that accepts multiple AC inputs plus a +270 VDC input. This COTS unit provides full-power, dual output, at a baseplate temperature of +85° C.
-
Product
Digital and Analog Communications
-
1. Design and implementation of RF oscillators and filters. 2. Design and implementation of analog AM and FM modulation and demodulation. 3. Design and implementation of digital and analog converter. 4. Design and implementation of ASK and FSK modulation and demodulation. 5. Design and implementation of PSK and QPSK modulation and demodulation.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 4 Channels, High Voltage Outputs
M2P.6576-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
