Analog Input Output
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
Product
NI-9475, 60 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module
780132-01
-
60 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module - The NI‑9475 works with a variety of industrial devices such as solenoids, motors, actuators, relays, and lamps. Each channel sources up to 1 A at levels up to 60 VDC and features isolation from … channel‑to‑earth ground.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
779521-01
-
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
720W to 1000W - Single Output
CPFE1000FI Series
-
*Smaller size than CPFE1000F*Baseplate cooled, no fan required*Protective coating option*I2C Interface*High Efficiency
-
Product
4 Channels of Strain Gauge Inputs for the SCS-800 Signal Conditioning System
SCS-817
-
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
Product
Low Input Bias Current Amplifiers (<100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
SHC68-68-A2, 68-Pin VHDCI Male to 68-Pin SCSI Female Analog Cable
157599-02
-
SHC68-68-A2, 68-Pin Male VHDCI to 68-Pin Female SCSI, 2m Cable. For use with the PXIe-6738 and PXIe-6739.
-
Product
Analog LCD Display Drivers
-
Analog Devices analog LCD display drivers provide a diverse range of options for industrial and commercial applications. The larger than standard rail-to-rail output swing offered by select members of this product line help enable applications requiring greater dynamic range than standard video op amps allow. The high slew rates and high capacitive drive capacity found in this portfolio make it ideal for LCD applications, while low supply current options support battery-powered technology.
-
Product
6-Ch Voltage Analog Input EtherCAT Slice IO Module
AMAX-5017V
-
Channels : 6 (Differential)Input Type : V,mVVoltage Range : ±150 mV, ±500 mV, ±1V, ±5 V, ±10 VInput Impedance : >10M ΩResolution : 16-bit with ±0.1% FSR accuracySample Rate : 100 sample/s (per channel)
-
Product
300W to 600W - Single Output
EVS Series
-
*Suitable for battery charging*300W Convection Cooled, 600W fan model*Adjustable Current Settings*Five year warranty
-
Product
Infiniium V-Series Oscilloscope: 33 GHz, 4 Analog Channels
DSOV334A
-
33 GHz analog bandwidth4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with low noise floor (2.09 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
REM-11175, 16-Channel (Output), 24 V, 2-, 3-Wire Digital Module for Remote I/O
784745-01
-
The REM-11175 is a digital output module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and … individual modules mounted on a DIN rail. You control the REM-11175 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. The REM-11175 features 2- and 3-wire spring terminal connection methods and circuit and overload protection.
-
Product
Input Digital Temperature Transmitter
HR6100
-
HighReach Measuring & Controlling System Co.,Ltd
The HR6100 input-type integrated temperature transmitter uses an imported temperature sensor to transmit and output RS485 standard signals through a built-in microprocessor. The product adopts the sealing structure of the liquid level transmitter, the waterproof cable outlet, the 316L stainless steel casing, And the temperature probe to the front end, which is suitable for occasions with special requirements on the installation dimensions.
-
-
Product
PXI 8 Slot BRIC 368x8 1-Pole Dual Analog Bus (8 sub-cards)
40-560A-121-368X8-M
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
High Definition Oscilloscope, 1 GHz Bandwidth, 4+16 Input Channels, 10 GS/s
HDO4104A-MS
-
1 GHz,4+16Ch,12-bit,10 GS/s,12.5 Mpts/Ch HD Mixed-Signal Oscilloscope w/ 12.1" WXGA Color Display.
-
Product
PXI 4 Slot BRIC 276x8 Dual Analog Bus (6 sub-cards)
40-560A-021-276X8-M
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
NI-9426, 24 V, 32 Channel (Sourcing Input), 7 µs C Series Digital Module
780030-01
-
24 V, 32 Channel (Sourcing Input), 7 µs C Series Digital Module - The NI‑9426 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels.
-
Product
Temperature Input Device
-
The Temperature Input Device is a thermocouple measurement device featuring InstantDAQ technology. InstantDAQ technology includes built-in software for viewing and logging data that automatically loads when you plug in the device, so you can instantly take temperature measurements with your PC. You can connect the Temperature Input Device to any USB port to use your PC as a display and monitor data in real time. The device is compatible with J, K, R, S, T, N, E, and B thermocouples.The Temperature Input Device includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Oscilloscope, 200 MHz, 4 Input Channels, 2 GS/s interleaved, 200 Mpts - interleaved
T3DSO2204A
-
200 MHz, 2 GS/s per Ch, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch DSO with 10.1" Color Display.
-
Product
Endevco Cryogenic Charge Output Accelerometers
-
PCB's acquisition of Endevco's full line of testing sensors means all Endevco sensors are now backed by PCB's Total Customer Satisfaction (TCS) guarantee. Endevco® cryogenic piezoelectric accelerometers are built specifically for measuring vibration under cryogenic conditions down to -452° F (-269° C). Signal outputs of these units are very stable even at extremely low temperatures. Their rugged internal construction is designed to withstand multiple cycles of thermal shock with steep temperature gradient. The accelerometers are self-generating devices that require no external power source for operation and contain no electronics. This allows them to operate below the -320° F (-196° C) limit of ICP accelerometers, down to -452° F (-269° C).
-
Product
35 W Triple Output, 6V, 2.5A & 20V, 0.5A
E3630A
-
Keysight basic DC power supplies offer essential features for a tight budget. The multiple output, 35-50 W, E3620A and E3630A provide dual and triple outputs; small, compact size for bench use; low-noise and excellent regulation; and overload indicator to monitor output. The Keysight 35W, triple output E3630A has three versatile outputs for benchtop applications; and is offers stable and reliable power plus essential features for manual testing.
-
Product
LXI Reed Relay Matrix - Single 128x4 Plugin, No Direct Y Access, 6 Analog Buses
65-221-112
-
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
Product
TB-4310 Front Mount Terminal Block for PXIe-4310, +/-600V Input
785022-01
-
96-Pin Female DIN to 82-Pin Female Screw Terminal, 10 V/600 V, PXI Module Mount Terminal Block.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 125 MS/s on 8 Channels, 80 MS/s on 16 Channels, 16 Single-Ended Inputs, 8 True Differential Inputs
DN2.596-16
-
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
FD-11603, 8-Channel, ±10 V Voltage Input Device for FieldDAQ
785639-01
-
The FD-11603 can measure up to eight channels with a voltage input range of ±10 V. It features 24-bit resolution with simultaneous sample rates up to 100 kS/s. The FD-11603 offers channel-to-channel isolation, which eliminates noise from ground loops and protects instrumentation circuitry from high-transient voltages. The FD-11603 has an ingress protection rating up to IP67 (dust- and water-resistant), can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. The FD-11603 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11603 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. The FD-11603 is ideal for test cell and outdoor environments.
-
Product
HPx-200 PCI Radar Input Card
-
The HPx-200 is a flexible, cost-effective PCI primary radar acquisition card that captures and processes one or two analogue or digital radar video signals from a single radar. The card is fully supported by SPx software, allowing modern radar processing to be added into legacy systems.
-
Product
Precision Integrated Analog Front End, Controller, & PWM for Battery Test & Formation Systems
-
The AD8452 combines a precision analog front-end controller and switch mode power supply (SMPS), pulse-width modulator (PWM) driver into a single silicon platform for high volume battery testing and formation manufacturing. A precision instrumentation amplifier (in-amp) measures the battery charge/discharge current to better than ±0.1% accuracy, while an equally accurate difference amplifier measures the battery voltage. Internal laser trimmed resistor networks establish the in-amp and difference amplifier gains (66 V/V and 0.4 V/V, respectively), and stabilize the AD8452 performance across the rated operating temperature range.
-
Product
MTM-DAQ-2: 16-Channel Analog DAQ Module
-
PRECISION ANALOG MEASUREMENTS: The MTM 16-Channel MTM-DAQ-2 Data Acquisition (DAQ) Module is engineered for precision measurements of analog voltages in manufacturing or R&D testing.
-
Product
PCI Card with input channels
PCI_LVDS_8R
-
The PCI_LVDS_8R has 8 channels of LVDS input. The channels are grouped two per Filter Xilinx. The input data is filtered, then written to the Input FIFO. There is one Input FIFO per LVDS channel. 1K x 32. One Latch Xilinx handles 4 LVDS channels. The data is read from the Input FIFO by the Latch Xilinx and either written to the SDRAM or the Output FIFO.
-
Product
Mixed Signal Oscilloscope - 350 MHz, 2 Analog Plus 16 Digital Channels
MSOX4032A
-
350 MHz2 analog plus 16 digital channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing at any time
