Temperature
a measurement of heat or cold.
-
Product
Field-installation Type Electric Conductivity Meter (Four-Wire Transmission, For Low-concentration)
HE-200C
-
HE-200 connects conductivity sensor (ESH/FS Series) and measures conductivity and temperature in the sample water. It is suitable for monitoring pure water/boiler water drainage recovery control and inline measurement of pharmaceutical water conductivity according to USP<645> quality guidelines.
-
Product
Polarimeter
ADP400 Series
-
The ADP400 Series from Bellingham + Stanley are single wavelength polarimeters suitable for sugar, food, chemical and pharmaceutical industries. These polarimeters are available with or without XPC - Xylem's patented internal Peltier temperature control system. Both models use standard polarimeter tubes with a maximum length of 200mm. For fast performance in the Peltier controlled version, stainless steel tubes should be used. Low volume samples are also catered for with the addition of stainless steel, luer taper tubes.
-
Product
Industrial Multimeter
CMM-40
-
Industrial multimeter CMM-40 was designed for the purpose of measurements of AC/DC voltage, AC/DC current, resistance, capacitance, frequency (electrical and electronic), duty cycle, temperature and also for testing diodes and continuity.
-
Product
Sensors
-
Detect your environment with various sensors. Motion, sound, vision, temperature, and more. 203 products.
-
Product
Solid State Active Synchro Control Differential Transmitter
-
Computer Conversions Corporation
The input is transformer isolated and accuracy applies over the operating temperature range and with +/-10% input amplitude and frequency variations. The operational amplifier outputs are not transformer isolated, and can be driven into external power amplifiers and Scott "T" transformers for 3 wire synchro outputs. A typical application of this series is in a conventional positioning servo system as a complex error processor. The use of the solid state CDX makes possible the design of servo systems that can be digitally programmed by direct computer input to the digital input of the SCDX.
-
Product
Laser Diode Driver
S-101
-
LD Driver slot module of FOTS system is an efficient module that is user centered, which can drive various kinds of laser diode for the use of optical signal transmission or light source. The module has a built in LD socket, in which LD of 14 pin butterfly type is installed, which makes it possible for the user to change the LD he or she wants to drive when needed. It is leaded to get rid of the inefficiency of expense, at which various types of expensive united source module needed are purchased. By operating monitoring PD and high-performance processor that are installed inside the module, the output power and temperature of LD can be driven accurately and stably. The laser diodes can be modulated internally in square, sinusoidal, and triangular waves and its output power and temperature can also be maintained the level set by the user. In order to realize the various functions, the efficient and multi-functioned control programs with high speed processor, LCD monitor or GUI for remote control are available.
-
Product
Dual Temperature
-
The Fieldpiece Dual-Temperature Accessory, model ATH4, measures two temperatures simultaneously using the included k-type, wrap tab beaded thermocouples. The technology inside the ATH4 provides superior temperature compensation in rapidly changing environments commonly found while performing field service. Use the ATH4 to find Delta T and just about any temperature split you want to measure. Displays T1, T2 and T1-T2 on your Fieldpiece meter, handle or data logger. It is included with the HVAC Guide® System Analyzer to get target superheat and for the Target Evaporator Exit Temperature test. Fieldpiece offers a wide variety of k-type thermocouples for various HVAC specific applications. Use pipe clamp T/Cs with the ATH4 to check for blocked filters.
-
Product
Temperature Probe Adapter
U1184A
-
Adapts thermocouple and temperature probes mini connector to dual banana inputs.
-
Product
Pressurized Foam Rheometer
-
Chandler Engineering developed an advanced tool for well completions designed specifically to measure the rheological properties of foamed systems under extended pressure and temperature conditions.
-
Product
MSR147WD Wireless Data Logger with plug-in Sensor
MSR147WD
-
Data Logger for measuring the physiological properties for textilesThe MSR 147WD, which is equipped with Bluetooth Low Energy (BLE) and a memory that is capable of storing 1 million measured values, enables you to reliably record and wirelessly monitor physiological parameters such as skin temperature and moisture level over long periods of time. The mini data logger has 5 connections for plug-in humidity and temperature sensors.
-
Product
Multifunction Calibrators
-
These bench multifunction calibrators source, simulate, and measure pressure, temperature, and electrical signals with exceptional precision. They can automate calibration procedures and maintain a wide range of temperature and pressure transmitters, multi-meters, pressure gauges, and more.
-
Product
General Purpose Probes
PIT-12
-
PIT-12 General Purpose Probe for Pressurized Systems - 12'' #304 stainless steel shaft. Diameter is 1/16''. Immersible. Maximum temperature 350°C, Time constant 0.5 Seconds. Shaft Terminated in a sub-miniature Type T Thermocouple plug. 10 foot Sub Miniature Type T extension lead supplied. Not isolated.
-
Product
Environmental Chambers
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood climatic chambers for battery can be tested under controlled temperature and humidity conditions, similar to the conditions under which batteries operate during their lifetime.
-
Product
Industrial Water Chiller Units
-
Wewon Environmental Chambers Co, Ltd.
The industrial chiller is divided into water-cooled chiller and air-cooled chiller. The water-cooled chiller must be equipped with cooling tower. Chilled water system is a machine that cools normal water through the chiller’s compressor to a certain temperature to strengthen the cooling process and generate a lot of heat.
-
Product
Custom Designed Environmental Chambers
-
Our strength lies in our ability to provide custom solutions to complicated testing needs. Our world-class design engineering team has the experience needed to tailor environmental test chambers to work in unison with existing machinery, unique size requirements, and custom testing conditions. Whether the environmental chamber is used for testing microchips and processors for leading computer manufacturers, or temperature, humidity, and altitude rated chambers for leading aerospace and defense contractors, our detail oriented team works to provide solutions that meet or exceed project requirements and industry standards for quality.
-
Product
Infrared Thermometers
-
Instant, less-than-a-second temperature readings of any surface, °F/°C switchableIdeal for food preparation, pharmaceuticals, field use, electronics, and safety inspectionFeatures minimum/maximum memory, average readings, and high/low audible alarms (Cat. No 4484)
-
Product
Temperature and Humidity Regulator
H3331-4
-
Relative humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Three two-state inputs.
-
Product
10G Distributed Feedback Lasers
-
Macom Technology Solutions Holdings Inc.
MACOM’s Distributed Feedback (DFB) laser diodes are designed for direct modulation uncooled operation up to10Gb/s. These products utilize patented Etched Facet Technology (EFT) for exceptional reliability with the following benefits: *Etched Facet Technology enabling high performance and product uniformity*Wide operating temperature range for wireless, PON and datacenter applications*No isolator required due to high back-reflection rejection
-
Product
Anemometer-Thermometer Data Logger
HD2103.2
-
Anemometer-Thermometer data logger which use hot-wire or vane probes to measure air speed, flow rate, and temperature inside pipelines and vents (for temperature Pt100 sensor with SICRAM module).
-
Product
IR Thermal Camera
AMG8833
-
This is the Thermal Camera FeatherWing: thanks to the Panasonic AMG8833 8x8 GridEYE sensor, it adds heat-vision to any Feather main board. Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top of your Feather board and let the board take flight!This part will measure temperatures ranging from 0°C to 80°C (32°F to 176°F) with an accuracy of +- 2.5°C (4.5°F). can detect a human from a distance of up to 7 meters (23) feet.
-
Product
Gel Strength Test System
LD-LGST-A10
-
Gel Strength Test SystemLD-LGST-A10is mainly used to measure the gel strength of gelatine under the stipulated environment. It has traveling accuracy ± 0.3 % and Test range up to 5 to 1000 g Bloom. It consists of Jelly Strength Tester, Constant Temperature Bath and Refrigerator. Sampling depth can be present arbitrarily in 1 to 60 mm. It consists four kinds of sampling measurement modes: single-step, maintaining, circulating and automatic.
-
Product
Engine Speed Control and Measurement (Test Set A)
MS 1100
-
*Checks the parameters such as current, voltage, speed, and turbine gas temperature of 804E and 811 engines Portable instrument*Testing of Automatic engine control system and after burner control system*Simulates the temperature signal derived from the engine TGT (Temperature Gas Turbine) thermocouples*Simulates the speed signal, NL (low pressure shaft speed signal) drive from the L.P shaft Probe*Indicates the current signal to the FCU solenoid derived from the engine control amplifier*Measure the TGT and NL simulated signal at static position*Measure the signal produced by the engine TGT thermocouples*Measure the NL signal produced by the LP shaft*Measure the NH (High-pressure shaft speed) signal produced by HP shaft*Indicates the solenoid current, produced by the engine control amplifier*Indicates the solenoid voltage, produced by the engine control amplifier*Used to test engine in both static and dynamic states
-
Product
Infrared Thermometers
-
Infrared thermometer plays an important role in production quality control, equipment maintenance and troubleshooting, energy saving, and other applications. Infrared thermometer measures temperature through non-contact method, producing quick and accurate results. It allows users to measure high temperatures at a safe distance.
-
Product
Setaflash ‘Series 8’ Active-Cool Closed Cup Tester
Elcometer 6910
-
The Elcometer 6910 Setaflash ‘Series 8’ Active-Cool Closed Cup Tester offers the same features as the Setaflash ‘Series 8’ Closed Cup Tester but is designed with a temperature range of -30°C to 135°C (-22°F to 275°F) with no external cooling required.
-
Product
Special Application Thermal & Pressure Mass Flow Controllers
-
Certain process vapors and gases require mass flow controllers of a special design specific to the material as well as process conditions. MKS offers both thermal mass flow controllers and pressure based mass flow controllers for these applications that require flow control at elevated temperatures and/or low pressure drop conditions given the source material characteristics.
-
Product
Barometer-Manometer-Thermometer
HD2114B.0
-
Barometer-Micromanometer-Thermometer with built-in barometric sensor (600…1100 mbar) for absolute, relative and differential pressure and temperature measurements.
-
Product
SF6 Density Meter Tester
JHMD-1
-
Xiamen Jiahua Electrical Technology Co.,Ltd
JHMD-1 is a smart tester. By using high accuracy core units, pressure sensor, A/D, D/A transducer, 32 bit ARM MCU and TI company’s high speed signal chip, it can automatically calibrate the density relay, measure pressure at signal activity temperature, convert pressure from any temperature to 20℃ standard pressure, print test data and save for review. It identifies the fault during the test. The whole procedure is under automatically operation, JHMD-1 is a high accurate, high stable, reliable tester.
-
Product
PRO Low Range Total Dissolved Solids Meter
MW401
-
MW401 is a Portable Low Range Total Dissolved Solids (TDS) Meter with Automatic Temperature Compensation. This instrument has been designed for aquariums, aquaculture, labs, and water conditioning applications to meet the needs for equipment suited from hobbist to professional. It is also a great meter for food labs, and water treatment applications.
-
Product
Digital Temperature Indicators
-
Premier's Temperature Indicators are commonly used for applications like monitoring of melting furnaces, determining completion of chemical analysis, monitoring of conveyors, checking completion of heating cycle, monitoring of moulds and dies, preheating temperature confirmation, determining temperature rise, preforming heat treatment, checking temperature in manufacturing process, transporting chemicals, laying pipelines with wall and sub sea temperature measurements.
-
Product
On-board Emissions Measurement System for NH3/N2O
OBS-ONE IRLAM Unit
-
The OBS-ONE IRLAM unit is an on-board emissions measurement system for analyzing the NH3/N2O under real-world driving conditions and supports our customer’s future regulatory development.The IRLAM unit combines with the GAS unit and the PN unit to measure the specified exhaust gas components, along with the exhaust gas flow rate, the GPS position, and the atmospheric conditions (temperature, humidity, pressure).
