-
Product
Time to Amplitude Converters and Calibrator
-
A Time-to-Amplitude Converter (TAC) can achieve exceptional precision by using an analog technique to convert small time intervals to pulse amplitudes. When a timing application demands picosecond precision, a time-to-amplitude converter is a prime candidate. A time-to-amplitude converter is a productive solution for measurements less than 10 μs when time resolutions from 10 ps to 50 ns are required.
-
Product
0.3Hz-6MHz Amplitude Display Functional Generator
MFG-8306
-
Features:*Max. frequency up to 15MHz*Single-chip function generating module provides high stability and low distortion waveforms*5 digit frequency display, 3 digit amplitude display.*Built-in frequency meter for testing external signal up to 20MHz*Linear and Logarithmic sweep function.*AM/FM function optional(Models with suffix “A”)*5W Power Output function optional(Models with suffix “W”)
-
Product
9KHz-2.1GHz, Spectrum Analyzer, Phase Noise<-98dBc/Hz, Amplitude Accuracy<0.7dB, 10.1" Color Display
T3SA3100
Spectrum Analyzer
9KHz-2.1GHz, Spectrum Analyzer, Phase Noise<-98dBc/Hz, Amplitude Accuracy<0.7dB, 10.1" Color Display.
-
Product
Two Channel Phase and Amplitude Noise Analyzer
DCNTS -190
-
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences. Its main extension is the Residual Noise measurement front-end which includes all necessary hardware to automatically measure residual noise on 2-ports devices either in RF frequencies or microwave. It could be a frequency multiplier or divider, an amplifier or any other phase coherent input to output device.
-
Product
0.3Hz-3MHz Amplitude Display Functional Generator
MFG-8303
-
Features:*Max. frequency up to 15MHz*Single-chip function generating module provides high stability and low distortion waveforms*5 digit frequency display, 3 digit amplitude display.*Built-in frequency meter for testing external signal up to 20MHz*Linear and Logarithmic sweep function.*AM/FM function optional(Models with suffix “A”)*5W Power Output function optional(Models with suffix “W”)
-
Product
Multicoupler, Rack Mount, 1U, Switchable Dual 2×4/1×8, P/LL/UL/S , Programmable Amplitude Balance
LS-16-R1-24SPLUS
-
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
Product
Multicoupler, Rack Mount, 1U, Switchable Dual 2×4/1×8, P, LL/UL/S/C, Programmable Amplitude Balance
LS-16A-R1-24SPLUSC
-
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
Portable RF Signal Generator
ACE 5400
-
The ACE 5400 portable RF signal generator has four carriers that can be activated individually or in any combination. Each frequency and amplitude is adjustable by the user. The ACE 5400's basic and straight forward performance is perfect for applications that require a precise, stable RF stimulus. Applications: Testing and aligning CATV return bands; Great for institutional networks.
-
Product
High Frequency Clock Divider Board
-
Alliance Support Partners, Inc.
Clock Divider is designed to divide high frequency signals, up to 2.5GHz, from 4 to 256 times. It will accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms. The clock division is controlled by 4 shunt jumpers. The circuit can be disabled and the divide by counter reset with 2 control signals. The on board regulator will accept voltages from 4.85 to 15.0V. The output is capable of driving 700mV Peak to Peak into 50 Ohms.
-
Product
ARINC 429 PXI Express Test & Simulation Instrument
PXIe-C429
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Phase Noise Analyzer
DCNTS
-
Noise eXtended Technologies S.A.S.
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences.
-
Product
Full Bandwidth Monitoring
Bluehorn System
-
When reproducing complex sounds, pattern relationships matter just as much as amplitude and frequency. Perfectly linear acoustical output requires phase re-alignment of the input signal. But thanks to the laws of physics, even the most accurate acoustic systems have introduced phase anomalies—until now.
-
Product
Flaw Detector & Thickness Gauge
DFX-8+
-
Measurement Gates: Two independent gates (Flaw), and three gates (thickness). Start & width adjustable over full range. Amplitude 5-95%, 1% steps. Positive or negative triggering for each gate with audible and visual alarms.
-
Product
Dual Channel Driver Card
40461
-
Two channels of 8 to 10 MHz drivers (25 V amplitude). The output voltage range is ±25V, with independent high and low voltage settings. The inputs to the Card are optically isolated. The card also contains voltage and current sense capability, which allows muxing of the current or voltage output measurements from all the Driver Channels in the system to a single DVM. The card allows independent programming of the rise and fall time of each channel as low as one nanosecond increments.
-
Product
Pulse Acquisition Board
MS 1818
-
*Used to measure the amplitude of discrete pulses driving relay coils/motors*Programmable No. of samples acquisition with programmable trigger option*Converts sine wave to square wave for pulse measurement*Measures amplitude of sine wave*16 Bit ADC interface*16 Bit data bus host interface*FPGA based design with flexible configuration*1K FIFO Storage
-
Product
Synthesizer Modules
LA19-15-03
-
We offer multi-decade synthesizer modules capable of operation beyond 8 GHz. A good example is theLA19-15-03 module capable of tuning from 300 kHz to 8 GHz with a 10 ppm settling time of 45 us forany size tuning step. It provides 10 Hz resolution, +15 dBm output with 30 dB of amplitude control.
-
Product
Low Noise Prepolarized Microphone
378A04
-
The 378A04 is a matched system that is comprised of a high sensitivity microphone and a low noise preamplifier that contains a built-in filter that enables the free-field response to remain flat over a wide frequency range. The system requires a minimum of 4 mA and measures to 6.5 dBA (5.5 dBA typical) within a cost efficient, prepolarized (0V) design. PCB's model 378A04, the industry's first prepolarized low noise microphone and preamplifier system allows you to measure extremely low amplitudes. In the past this was only possible with externally polarized solutions. With a typical noise floor of 5.5dBA, this microphone system delivers all of the benefits commonly associated with prepolarized systems.
-
Product
Astronics PXIe-2461, 235 MHz FrequencyTime Interval Counter
784197-01
Counter/Timer Module
PXIe, 42 V, 2-Channel PXI Counter/Timer Module—The Astronics PXIe‑2461 is a high-performance counter/timer module that provides easy-to-use automatic measurement functions, including phase, pulse, peak, rise/fall time, time interval and ratio measurement, all with high resolution. It features nine digits per second resolution, programmable measurement timeout, and nine different arming modes. You can set the Astronics PXIe-2461 to measure timing and amplitude characteristics in one of two voltage ranges: ±5.1 V or ±42 V.
-
Product
Wideband Power Analyzer
2335A
-
Clarke-Hess Communications Research
The Model 2335A Wideband Power Analyzer is a precision, high accuracy, high frequency auto-ranging instrument which measures and displays true rms Voltage, true rms Current, and true mean Power over a frequency range from dc to more than 1MHz. Full scale Current and Voltage inputs are typically measured within 0.1% of the amplitude reading to at least 500kHz. The corresponding Power is typically measured to within 0.1% of the input Volt-Amperes to 250kHz and to within 0.2% of the input Volt-Amperes to 500kHz for loads having any Power Factor.
-
Product
Shock Control
-
Shock testing simulates an extreme event that a unit under test is exposed to during handling, shipment, explosive event and/or daily use (e.g. dropping an object). The profile for this type of testing is defined by the shape of the time domain waveform together with its amplitude and duration. The m+p VibControl vibration control system offers full functionality for classical shock and shock response spectrum testing as well as for tests using external pulses or the capture of transient signals.
-
Product
Qualification and Quality Control Tests
Techsquare
-
New IEC standards, IEC 60034-18-41 and IEC 60034-18-42, have been issued to define the procedures for testing partial discharge inception voltage and the long-term performance (endurance) of Type I and Type II insulation systems used in rotating machines fed from voltage converters. Voltage impulse generators are required at least to test turn insulation, but they would be recommended for any testing under power electronics supply because of their capability to simulate the real electrical stress conditions. More generally, any type of electrical insulation system when subject to impulsive voltage waveform during life should be carefully evaluated in terms of partial discharge and endurance behaviour. This is why voltage impulse generators able to provide impulses with controlled amplitude and frequency are needed to face this new testing challenge.
-
Product
Dual Channel Driver Card
42460
-
Two channels of 32 MHz clock drivers with up to 20 volt amplitude. The output voltage range is ±20 V, with independent high and low voltage settings. The inputs to the Card can be optically isolated. The card also contains voltage and current sense capability, which allows muxing of the current or voltage output measurements from all the Driver Channels in the system to a single DVM. The card allows independent programming of the rise and fall time of each channel one nanosecond increments.
-
Product
Scalar Network Analyzers
-
An RF network analyzer used to measure amplitude properties like VSWR and Return loss of Device Under Test.
-
Product
Portable Electricity Meter Testers
EE-120A-3S + EE-500V-3
-
The Phantom Load is able to generate three-phase voltages and currents with unprecedented stability and measurement accuracy. The amplitude and phase-shift of each current and voltage is individually adjustable. All types of electricity meters – mechanical or electronic, for active, reactive or apparent energy, single-phase or three-phase – can be tested with the Energy Standard. The following meter tests can be carried out with the EE Test System: Error Test, Register Test, No Load Test and Starting Current Test. Full analysis of the customer load can also be performed, if current clamps have been ordered. All test results ( maximum 3 Test Plans, 5 Manual Measurements and Customer Load Analysis) can be saved in one file. 100 saved files can be viewed on the LCD display or transferred to a PC via USB port.
-
Product
RF Signal Generator With 1.5 And 3GHz Models
TGR205x Series
-
150kHz to 3GHz (TGR2053) and 150kHz to 1.5GHz (TGR2051) frequency rangeHigh signal purity, phase noise <-117dBc/Hz (typical) at 1GHz output and 10kHz offsetAmplitude range of -127dBm to +13dBm0.1dBm amplitude setting resolutionInternal or external analogue modulations (AM, FM, PM)Amplitude can be set in dBm, dBμV or in linear Volts.Internal or external digital modulations - ASK, OOK, FSK, 3FSK, 4FSK, GFSK, MSK, GMSK, HMSK & PSK with U01 optionModulation SynchronisationFast amplitude and/or frequency sweeps with comprehensive triggering5ms sweep settling time1ppm frequency accuracy, <1ppm drift in first yearModulation waveform output on the rear panelInternal waveforms include: Sine, Square, Ramp, Triangle, PRBS (various lengths) and user-defined patternSimple operation with the colour touch screenProgrammable via USB, LAN (LXI) and GPIB (optional), SCPI compatibleCompatible with previous Aim-TTi RF generators
-
Product
PXI Amplifier And Attenuator Modules
-
Pickering's PXI Amplifier and Attenuator Modules include our accurate DC to 3GHz programmable attenuator has a 1dB step resolution, allowing it to adjust signal amplitudes for optimum measurement by other devices. The other programmable attenuator available has a bandwidth between 10MHz and 6GHz available in triple or hex formats.
-
Product
Hybrid Power Divider, 2 GHz to 26.5 GHz
87304C
Power Divider
The Keysight 87304C hybrid power divider is designed for power splitting applications that require minimal insertion loss and high isolation between ports. It has insertion loss between the main line and output port which is 1 to 2 dB less than equivalent resistive power splitters. It is designed for critical signal processing applications; phase and amplitude tracking between the two output ports is controlled and specified.
-
Product
Turnkey or PCI Cards and Software
WinCAT Systems
-
# True fast transient recorder system.# 4, 8 or 16 channel models.# 1 MHZ aggregate 12 bit sampling, resolution equal to 0.024% of full scale.# 13 record lengths, user selected, 132 msec to 1,320 sec in typical 1-2-5x scope progression.# 6 programmable front end gains, user selected, equal to 0.4, 1, 2, 4, 10 and 20 volts full scale.# Software converts digitized voltages to Engineering units.# Digital Triggering, Amplitude and slope, in engineering units from digitized input signals.
-
Product
Signal Generator
-
Shijiazhuang Suin Instruments Co., Ltd.
One of a class of electronic devices that generates electrical signals with set properties of amplitude, frequency, and wave shape.
