-
Product
Fiber Channel Simulyzer
-
Avionic Interface Fiber Channel SimulyzerTM products are multifunctional, high-performance Fiber Channel interface and test boards. The products have both a data generation / simulation function and a monitor / analysis function on one board. Avionic Interface Fiber Channel products can be used with the most popular upper layer protocols FC-AE-ASM, FC-AE-1553, FC-AE-RDMA and FC-AE-AV. All FibreChannel products use multiple processors with large onboard RAM.
-
Product
Digital Output Board
VME-2128A
Digital Output Board
VME-2128A 128-bit High-Voltage Digital Output Board with Built-in-Test
-
Product
Relay Output Board
VME-2232A
Relay Output Module
VME-2232A is a 32-Channel Relay Output Board with Built-in-Test (BIT). Software compatible with the VMIVME-2232 and the VMIVME-2533.
-
Product
Surface And Subsurface EW System Tester
MS 1119
-
CPCI Based BTA is used to test ECM System Processor (80386 & 8051) Boards. This system consists of a Single Board Computer (SBC), CPCI RS422 Communication and Bus Interface Board (CBI), CPCI Digital Input & Output (DIO) Board and CPCI Analog Input & Output (AIO) Board to provide the necessary input/output signals to/from the board to be tested.
-
Product
PCBA Pattern Analyzer
A222917
-
Chroma A222917 is a multi-functional PCBA main board board signal test device for display. It has ultra high speed LVDS (Low -voltage differential signaling) as image signal analysis core to provide high efficiency and stability test quality.
-
Product
IC Test Clips
-
Low-profile fine-pitch chips, desnely populated boards, or vertical boards, Pomona test clips connect you with confidence.
-
Product
Quadruple Function Tester with Shielded HF Test Chambers
UTP 9011 RF
-
Circuit boards are the heart of all electronic devices. To ensure the reliable function of these boards, detailed tests are essential.Our board-level tester UTP 9011 RF works safely, quickly and cost-optimized at circuit board level. Our interchangeable adapters are particularly efficient in this system, with which you can even test different test items at the same time. The shielded NOFFZ HF test chamber always ensures consistently good results.
-
Product
Test Board For QSFP28 Transceiver
EQSFP28
-
The OPTELLENT EQSFP28 is a cost-effective and convenient test board for testing QSFP28 optical transceivers in R&D and manufacturing environments. The EQSFP28 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The EQSFP28 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
Product
1149.6 Boundary Scan Feature, GTE 10.00p
K8213A
-
Keysight’s Interconnect Plus Boundary Scan 1149.6 feature enables all the tools required to develop and execute this test method on the board under test. Compared to the 1149.1 standards, the 1149.6 standards define test methods for the boundary scan devices that are designed with AC coupled signals or differential nets needed for high-speed operations of the device.
-
Product
Meter Test Board
MTB-3200
-
Run standard meter accuracy tests and complex meter accuracy tests under widely varying loading conditions with TESCO’s Meter Test Board (MTB-3200). TESCO’s Three Phase Meter Test Board (MTB-3200) is an innovative meter accuracy test system offering unsurpassed functionality and ease of use. All of the features needed to test meters today and tomorrow are standard.
-
-
Product
Hign Speed Bare Board Test System By Non-Contact Test Technologies
SX-750SUPERⅣ
-
Suitable for a wide range of applications. Can be connected to a wide range of machines: from hand press to reel mechanism and in-line mechanism. We offer docking with our customers own machines. Compact main tester simplifies integration via installation inside a mechanism. If requested, we will perform a study to decide which functions should be added.
-
Product
Vacuum Test Fixtures
Series 63
-
The VT Series 63 vacuum test kits provide both an affordable and versatile solution for printed circuit board testing requiring vacuum actuation and a Genrad 2270/71 interface. The VT Series 63 kits, available in Single and Dual Well models, incorporate a robust design which includes a variety of chassis sizes and depths for additional hardware and components used in Functional Test. Tooling holes on both the top diaphragm plate and probe plate for accurate drill datum. The interface will accommodate up to 11 I/O blocks with a single vacuum port.
-
Product
Power-off Circuit Board Testing
Huntron® Trackers®
-
Adding diagnostic tools to enhance your circuit board test capabilities is an important part of any electronic repair environment.Huntron Tracker power-off circuit board test uses analog signature analysis to detect and isolate component faults on boards beyond power-on functional testing. By comparing Tracker signatures from a working circuit board to the signatures of a non-working board, you can troubleshoot down to the component level.
-
Product
Clamshell Type Mechanical Fixtures
Series 31
-
The GR Series 31 dual well mechanical kits provide a solution to printed circuit board testing that requires the benefits of GR2270 style (VG) interface compatibility and the advantage of testing two devices on the same test fixture. These can be similar devices, or devices that are used together in a functional test.
-
Product
VME Test Extender 6U/220mm J1/J2
111EXT6122-012X
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
Digital Input Board
VME-1129
Digital Input Board
VME-1129 128-bit high voltage digital input board with Built-in-Test and input filter. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297), with the following mnemonics: A24:A16: D32/D16/D08 (EO): Slave:39/3D: 29/2D Form Factor: 6U
-
Product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
-
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
Product
Test Probes and Pins
-
Spring Loaded Test Probes for Circuit Board Testing, "Pogo Pins" Test Electronics sources and stockes a large variety of Test Probes and Spring Loaded Test Pins. Let our applications engineers help you find the correct pin for your test fixture application.
-
Product
CPCI Load Boards 6Ux160mm
1940000135-0000
-
The 6U cPCI Load Board functions to test a system's cooling capabilities by first applying the load to the power supply for verification and finally creating the necessary heat to confirm chassis cooling.
-
Product
Bare Board Electrical Testing
ProbeMaster
-
ProbeMaster is the complete software solution to your shops needs in bare board electrical testing. ProbeMaster is PentaLogixs top-of-the-line software package that combines all of the power of the PentaLogix CAM and Fixturing packages with support for moving probe, Netlist Comparison and other robust features.
-
Product
50 Pin Breakout Interface
VSI-Breakout-50
-
The VSI-Breakout-50 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
VME Test Extender 3U/220mm J1
111EXT3122-11XX
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
Test Set
TS® 22
-
The TS22 Test Set’s unique built-in one-way amplified speaker provides three audio levels for hands-free listening and use with automated voice response systems. Multiple memories enable storage of nine 18 digit telephone numbers in repertory dialer (speed dialing) for easy access to test boards, the central office and other frequently called numbers. The last number redial feature eliminates the need to re-key your last entry. The TS22 Test Set offers an unbeatable combination of reliability, durability and expanded utility.
-
Product
VME Test Extender 6U/220mm 64X with P0
116EXT6122-0125R
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
Test Board For QSFP+ Transceiver
EQSFP10
-
The OPTELLENT EQSFP10 is a cost-effective and convenient test board for testing QSFP/QSFP+ optical transceivers in R&D and manufacturing environments. The EQSFP10 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The EQSFP10 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
Product
Test Board For SFP+ / SFP28 Transceiver
ESFP280
-
The OPTELLENT ESFP280 is a cost-effective and convenient test board for testing SFP/SFP+/SFP28 optical transceivers in R&D and manufacturing environments. The ESFP280 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The ESFP280 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
Product
Engineering Services
-
In addition to the highest quality test programming, maximizing board coverage, and efficient board testing, TTCI offers a full array of other engineering services, including CCA (Circuit Card Assembly) Testing, Design for Test, ASTER TestWay electrical design for test analyzer, Feasa LED analyzer, SMH Technologies FlashRunner in-system programmer, finite element analysus, installation, reverse engineering of Gerber to CAD, Training, Test System PC, Hardware, and Software Upgrades, and more.
-
Product
VME Test Extender 9U/400mm J1/J2/J0
111EXT9140-0120
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
Power Supply Testers
-
Qmax Test Technologies Pvt. Ltd.
Power Supply Tester is an integrated package of hardware such as AC/DC Power Sources, DC Loads, Noise Measurement Unit, and DMM etc configured as per user applications, which makes it suitable for testing wide range of Power Supplies and provide economic solution for testing AC/ DC and DC/DC power supplies and converters. The Power Supply Boards that passed in the first level of screening for Go-No Go tests will undergo a second level testing. The second level of testing measures all the key parameters of the power supply such as line regulation, load regulation, efficiency etc and check whether the results are within the mentioned limit, if not declare the UUT (Power Supply Board Under Test) as a failed one.
