-
product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
product
Digital Input Board
VME-1129
VME-1129 128-bit high voltage digital input board with Built-in-Test and input filter. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297), with the following mnemonics: A24:A16: D32/D16/D08 (EO): Slave:39/3D: 29/2D Form Factor: 6U
-
product
Bare Board Electrical Testing
ProbeMaster
ProbeMaster is the complete software solution to your shops needs in bare board electrical testing. ProbeMaster is PentaLogixs top-of-the-line software package that combines all of the power of the PentaLogix CAM and Fixturing packages with support for moving probe, Netlist Comparison and other robust features.
-
product
Wireless Functional Test Fixtures
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
-
product
Silicon Test & Yield Analysis Solutions
Tessent®
The Tessent product suite combines features of deterministic scan testing, embedded pattern compression, built-in self-test, specialized embedded memory test and repair, and boundary scan, as well as board and system-level test technologies. This comprehensive silicon test and yield analysis solution is built on the foundation of the best-in-class solutions for each test discipline
-
product
Flying Probe Tester
FA1811
Designed specifically for package board testing, the FA1811 achieves both high-precision contact with a total probing precision of 10 μm, and a testing speed rivaling generic flying probe testers to meet ever increasing demands for greater analytical power, faster testing speeds and reduced costs.
-
product
1149.6 Boundary Scan Feature, GTE 10.00p
K8213B
Keysight’s Interconnect Plus Boundary Scan 1149.6 feature enables all the tools required to develop and execute this test method on the board under test. Compared to the 1149.1 standards, the 1149.6 standards define test methods for the boundary scan devices that are designed with AC coupled signals or differential nets needed for high-speed operations of the device.
-
product
37 Pin Breakout Interface
VSI-Breakout-37
The VSI-Breakout-37 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
product
Adjustable Press Plate Bed of Nails Testers
Prober Adjustable Family
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
product
25 Pin Breakout Interface
VSI-Breakout-25
The VSI-Breakout-25 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
product
Software & Hardware Interface
XJAPI
The XJAPI is a simple-to-use DLL Application Program Interface (API), designed to give you low-level access to the JTAG chain via either the XJLink or the PXI hardware, allowing easy integration with a wide range of other systems such as development/evaluation boards, test systems
-
product
Generic Probe Cards, PIB's, and Loadboards
Test Spectrum can provide generic Probe Cards, Probe Interface Boards (PIB), and loadboards. Choose from existing configurations already designed, or a generic test board for your specific tester configuration can be designed quickly.Teradyne J750 Probe Card and PIB; Teradyne Integra Flex PIB; Teradyne Ultra Flex PIB; Teradyne Catalyst PIB; Credence Quartet PIB (Probe Interface Board); Advantest 93K 1024 PIB
-
product
Test Services For Circuit Board
Acculogic Contract Testing Services group with multiple locations in United States, Canada, Germany and China provides Cost Effective, On-Demand (Quick-Turn) testing service. Our circuit board assembly test services include defect analysis, In-Circuit, Boundary Scan JTAG and Functional testing on industries most widely used test platforms.
-
product
Differential Sensor, Wide Dynamic Range, 100 MHz
CX1105A
The CX1105A ultra-low noise differential sensor is a dedicated accessory for the CX3300 series and enables dynamic current measurements from 1 μA to 100 A under up to 100 MHz bandwidth with existing shunt resistors on your test board.
-
product
FPGA Test System
DO-254/CTS
DO-254/CTS™ is a fully customized hardware and software platform that augments target board testing to increase verification coverage by test and satisfy the verification objectives of DO-254/ED-80. The target design runs at-speed in the target device mounted on the custom daughter board. The simulation testbench is used as test vectors to enable requirements-based testing with 100% FPGA pin-level controllability and visibility necessary to implement normal range and abnormal range tests. The FPGA testing results are captured at-speed and displayed using a simulator waveform viewer for advanced analysis and documentation.
-
product
Backplane Test System
402HV
Our model 402HV is the result of 25 years of high voltage / high pin count test systems experience. We produced our first high voltage system back in 1985. It was programmable up to 600 volts / 600 Mohms and had over 49,000 test points. It could test a 5k point board in less that 15 seconds. Since then we have built hundreds of high voltage test systems, with our highest voltage system capable of testing up to 2000 Volts DC / 1500 Volts AC. (One of our 600 volt systems, built in 1986 is still in operation testing boards for a defense contractor.)
-
product
Test Fixtures
Test fixtures are a product for the test and the testing of printed circuit boards. The test adapters offered by uwe electronic are suitable for both manual testing and automated testing with vacuum operation. The test fixture can be either fully equipped and wired or delivered without installed components. Pneumatic, Mechanical and Vacuum Fixtures.
-
product
RELIABILITY BOARD (Reliability Test Board)
The reliability test board is used for testing of HAST, THB, HTOL, BURN-IN, etc. It is a product that evaluates the environmental test and durability when applied to actual products such as lifetime test, high temperature, low temperature, high humidity and thermal shock
-
product
4X14 Gb/s QSFP/QSFP+ Evaluation Board
EV-QSFP-174
The EV‐QSFP‐174 QSFP/QSFP+ Host Test Board comes complete with Windows based software (Windows XP & above) to enable intuitive memory map programming and testing, controlled via a mini B USB port. It is designed to simulate an ideal environment for QSFP/QSFP+ transceiver module testing, characterization and manufacturing test. Its high speed properties make the host board as electrically transparent as possible, allowing for a more accurate assessment of the module’s performance.
-
product
THRU HOLE BARE AND LOADED BOARD TEST PROBES
SERIES 80
MAXIMUM CURRENT: 6 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,35 mOHMS meanMaterials and FinishesPLUNGER: Heat treated berylliumcopper, 24 Kt gold plated over nickelBARREL: Nickel silver with 24 Kt goldplated ID and OD over nickelSPRING: (Standard) Beryllium copper,silver plated. (-1) Stainless steel,silver plated
-
product
Calibration Pulse Processor
2401
TESCO’s Calibration Pulse Processor (Catalog No. 2401) adapts to any Next Generation three phase test board to directly calibrate with three independent single phase standards.
-
product
Burn-In Board Tester
Focus-275
Focus275 is a tester for burn-in board.It can improve reliability of burn-in board by inspecting boards for burn-in test by Focus275 regularlyBoth short open test and component test can be done by sending electric signals for special socket contactor and edge part.
-
product
Massively Parallel Board Test System
I7090
The Keysight i7090 is a massively parallel board test system designed to help PCBA test engineers improve manufacturing efficiency while reducing costs. Unlike traditional in-circuit testers, the i7090 supports up to 20 In-Circuit Test cores in parallel, which means engineers can test multiple Units Under Test (UUTs) simultaneously without the need for multiple systems. This reduces scaling and infrastructure costs and frees up valuable testing space.
-
product
Power-off Circuit Board Testing
Huntron® Trackers®
Adding diagnostic tools to enhance your circuit board test capabilities is an important part of any electronic repair environment.Huntron Tracker power-off circuit board test uses analog signature analysis to detect and isolate component faults on boards beyond power-on functional testing. By comparing Tracker signatures from a working circuit board to the signatures of a non-working board, you can troubleshoot down to the component level.
-
product
VME Test Extender 3U/220mm J2
111EXT3122-12XX
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
Engineering Services
In addition to the highest quality test programming, maximizing board coverage, and efficient board testing, TTCI offers a full array of other engineering services, including CCA (Circuit Card Assembly) Testing, Design for Test, ASTER TestWay electrical design for test analyzer, Feasa LED analyzer, SMH Technologies FlashRunner in-system programmer, finite element analysus, installation, reverse engineering of Gerber to CAD, Training, Test System PC, Hardware, and Software Upgrades, and more.
-
product
Inline test system for FCT, ICT, ISP and Boundary Scan for Automated Operation
LEON InLine
High production volume often requires inline solutions with fully automated product Handling – the LEONlnline is a complete Inline Board Test Solutions for printed circuit boards. It integrates a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors.
-
product
VME Test Extender 3U/400mm J2
111EXT3140-12xx
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
Clamshell Type Mechanical Fixtures
Series 71
The VP Series 71 dual well mechanical kits provide a solution to printed circuit board testing using the Virginia Panel ITA G12 Interface and the advantage of testing two devices. This can be similar devices, or devices that are used together in a functional test. The VP Series 71 Kits have the same available features and options as the Series 70 Kit and are available with or without the ITA G12 Interface.
-
product
TIM Characterization Tools
Thermal Engineering Associates, Inc.
Combining Thermal Test Vehicles (TTVs) with Thermal Test Boards (TTBs) results in a set of tools that perform the basis for TIM thermal characterization under application-oriented measurement conditions. Availability of these tools creates a de facto standard that enable both TIM manufacturers and TIM users to compare measurement results under the same conditions.
