-
Product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
-
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
Product
TIM Characterization Tools
-
Thermal Engineering Associates, Inc.
Combining Thermal Test Vehicles (TTVs) with Thermal Test Boards (TTBs) results in a set of tools that perform the basis for TIM thermal characterization under application-oriented measurement conditions. Availability of these tools creates a de facto standard that enable both TIM manufacturers and TIM users to compare measurement results under the same conditions.
-
Product
Fiber Channel Simulyzer
-
Avionic Interface Fiber Channel SimulyzerTM products are multifunctional, high-performance Fiber Channel interface and test boards. The products have both a data generation / simulation function and a monitor / analysis function on one board. Avionic Interface Fiber Channel products can be used with the most popular upper layer protocols FC-AE-ASM, FC-AE-1553, FC-AE-RDMA and FC-AE-AV. All FibreChannel products use multiple processors with large onboard RAM.
-
Product
VME Test Extender 3U/400mm J2
111EXT3140-12xx
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
Flying Probe Tester
FA1811
-
Designed specifically for package board testing, the FA1811 achieves both high-precision contact with a total probing precision of 10 μm, and a testing speed rivaling generic flying probe testers to meet ever increasing demands for greater analytical power, faster testing speeds and reduced costs.
-
Product
High-Speed Embedded Host Electrical Test Board
HSEHET
-
High-Speed Embedded Host Electrical Test Board is approved by USB-IF, specifically designed for the electrical test of USB embedded host products.
-
Product
Software
D2B
-
The unique capabilities of Teradyne's D2B software enable EMS and OEM manufacturers and partners to interconnect their global enterprises to optimize printed circuit board assembly test and inspection efficiencies early in the manufacturing / build cycle. D2B is a powerful suite of solutions that provides a standards-based architecture that supports GenCAM and ODB++ file formats enabling electronic manufacturers to outperform their competition, maximize profitability, and get to market first.
-
Product
IC Test Clips
-
Low-profile fine-pitch chips, desnely populated boards, or vertical boards, Pomona test clips connect you with confidence.
-
Product
PXI 16x SPST High Voltage Reed Relays
40-310-101
Reed Relay
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
Semi-automatic Three-phase kWh Meter Test Bench
SY8310
-
Hong Kong Songyang Industrial Ltd.
The new SY8310 series semi-automatic three phase energy meter test board, designed according to International Standard, is a newly developed ideal measuring equipment for energy meters. The equipment can be operated easily through test board button to preset directly all data of meter under test and test process.
-
Product
Flying Probe Testers
-
Flying probe test systems require no test fixturing, have few restrictions on board access, and can test boards with virtually unlimited number of nets. These systems also allow developers to complete test programs in a short time.
-
Product
Printed Circuit Board Testing Solutions
-
IES Systems is a turnkey test systems solution provider with 10 years of proven experience in printed circuit board testing solutions. Our experienced engineers design electro/mechanical solutions to interface between your product and our custom designed test instrumentation. We provide a complete solution to your PC board testing needs.
-
Product
Kelvin Test Contactor
nano
-
nano Kelvin™ test contactor is a well-established Cantilever Kelvin test contactor with proven performance in the automotive market and further increasing popularity due to the robustness and reliability of the product.Featuring a small imprint area, contact motion decoupled from the test board and simple and cost-efficient test boards.
-
Product
MTB Calibration Adapter
2450-CAL-30
-
The MTB Calibration Adapter (Catalog No. 2450-CAL-30)is a socket adapter that’s designed to bring phase A, B, and C current and potentials of a TESCO Multi-Position Test Board to an external RD-30 reference standard for calibration of the Test Board.
-
Product
Clamshell Type Mechanical Fixtures
Series 70
-
The VP Series 70 Mechanical Test Kits provide a solution to printed circuit board testing using the Virginia Panel ITA G12 Interface.
-
Product
Dynamic Digital I/O With Per Channel Timing, Programmable Logic Levels And PMU PXI Card
GX5296
Digital I/O Module
The GX5296 offers advanced dynamic digital I/O performance and capabilities in a single slot, 3U PXI format. The 32-channel, GX5296 features timing per pin, multiple time sets, data formatting, and an advanced sequencer – providing users with the capability to emulate and test complex digital busses for system, board or device test applications. Offering sub-nanosecond edge placement resolution per pin and a PMU per pin, the GX5296 has the ability to perform both DC and AC parametric testing. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
Product
Clamshell Type Mechanical Fixtures
Series 11
-
The MT Series 11 dual well mechanical kits are an affordable solution to printed circuit board testing with the advantage of testing two devices. These can be similar devices, or devices that are used together in a functional test. The Series 11 Kits have the same available features and options as the Series 10 Kits.
-
Product
Non-Multiplexed High Speed Transient Function Card
-
Identified by its ADC per channel and on-board memory, it typically operates at per channel sampling rates which in aggregate would overwhelm any communication system. Data is stored on board during a test and transmitted to a host computer following completion.
-
Product
LXI High Voltage Matrix 2-pole 300x2
60-310-302
Matrix Switch Module
The 60-310 is a 2-pole Matrix Module available in 300x2, 200x2 and 100x2 formats. It is capable of cold switching 1000VDC and has a maximum carry current of 1A. It is designed for high voltage applications including circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
Silicon Test & Yield Analysis Solutions
Tessent®
-
The Tessent product suite combines features of deterministic scan testing, embedded pattern compression, built-in self-test, specialized embedded memory test and repair, and boundary scan, as well as board and system-level test technologies. This comprehensive silicon test and yield analysis solution is built on the foundation of the best-in-class solutions for each test discipline
-
Product
VME Test Extender 3U/220mm J2
111EXT3122-12XX
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
VME Test Extender 6U/220mm Universal
110EXT6122-000X
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
MECHANICAL TEST FIXTURE KITS
TX-MT-SERIES
-
Test-X MT Series mechanical kits are an affordable solution to printed circuit board testing. With multiple configurations and available options, this product is sure to meet your testing needs. The MT Series features a hinged 3/8" FR4 probe plate, tooling holes for accurate drilling, and side handles for easy transportation.
-
Product
Debug Fixture
-
With at-speed test, debug can easily become a problem: If test points are on the bottom, as is often the case for test processing, then this requires the board to be flip over for the debug. However, during at-speed testing, key devices and signal paths are often on the topside. IST Engineering has in-house expertise with debug fixtures, which allow the test technician to flip over a test board, or even hold it vertically for dual-sided access, while still running the Device-Under-Test at full-speed through card-edge connectors - whether these are standard DIN type or F or N type co-ax connectors. The debug stations are constructed robustly, with metal frames and high-grade flexible cabling and can also be used as backup test stations in a manufacturing flow. They can be built with custom machined waveguide connections for RF/Microwave applications, or with standard, off the shelf connectors, as defined by the application. A number of these debug fixtures are in production use with a range of customers.
-
Product
Combination Board Functional Test System
QT 4256 ATE
Functional Test
Qmax Test Technologies Pvt. Ltd.
QT 4256 ATE is a combination Board Functional Test System , a main frame Automated Test Equipment (ATE) which can be configured up to maximum of 1280 Bi-directional digital channels ideal for testing circuit card assemblies of high level of complexity and whether it is a legacy or new generation PCB.
-
Product
Test Probes and Pins
-
Spring Loaded Test Probes for Circuit Board Testing, "Pogo Pins" Test Electronics sources and stockes a large variety of Test Probes and Spring Loaded Test Pins. Let our applications engineers help you find the correct pin for your test fixture application.
-
Product
Calibration Pulse Processor
2401
-
TESCO’s Calibration Pulse Processor (Catalog No. 2401) adapts to any Next Generation three phase test board to directly calibrate with three independent single phase standards.
-
Product
Test Engineering Projects
-
Precision Development Consulting Inc
Fiber Optics Test System, Data Collection, Trident Missle Components, PC Board Functional Test and Bearing Tester
-
Product
Software & Hardware Interface
XJAPI
-
The XJAPI is a simple-to-use DLL Application Program Interface (API), designed to give you low-level access to the JTAG chain via either the XJLink or the PXI hardware, allowing easy integration with a wide range of other systems such as development/evaluation boards, test systems
-
Product
Extender Boards
-
VECTOR Electronics and Technology, Inc.
Extender boards are designed to bring a circuit card completely out of a card cage or enclosure so that it can be tested or debugged. This provides access to both sides of the test board.
